View NL160120BC2714_4874308.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

document number: dod-pd-1335 (1st edition) published date: february 2006 cp(n) ? nec lcd technologies, ltd. 2006 all rights reserved. 1 all information is subject to change without notice. please confirm the sale s representative before starting to design your system. tft color lcd module nl160120bc27-14 54cm (21.3 type) uxga lvds interface (2 ports) data sheet dod-pd-1335 (1st edition) www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 2 introduction the copyright to this document belongs to nec lcd technologies, ltd. (hereinafter called "nec"). no part of this document will be used, reproduced or copied without prior written consent of nec. nec does and will not assume any liability for infringement of patents, copyrights or other intellectual property rights of any third party arising out of or in connection with application of the products described herein except for that directly attributable to mechanisms and workmanship thereof. no license, express or implied, is granted under any patent, c opyright or other intellectual property right of nec. some electronic parts/components would fail or malfuncti on at a certain rate. in spite of every effort to enhance reliability of products by nec, the possibility of failures and malfunction might not be avoided entirely. to prevent the risks of damage to death, human bodily injury or other property arising out thereof or in connection therewith, each customer is re quired to take sufficient measures in its safety designs and plans including, but not limited to, redundant system, fire-containment and anti-failure. the products are classified into three quality grades: "standard" , "special" , and "specific" of the highest grade of a quality assurance program at the choice of a customer. each quality grade is designed for applications described below. any customer who intends to use a product for application other than that of standard quality grade is required to contact an nec sales representative in advance. the standard quality grade applies to the products developed, designed and manufactured in accordance with the nec standard quality assurance pr ogram, which are designed for such application as any failure or malfunction of the pr oducts (sets) or parts/components incorporated therein a customer uses are, directly or indirectly, free of any damage to deat h, human bodily injury or other property, like general electronic devices. examples: computers, office automation equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment, industrial robots, etc. the special quality grade applies to the products developed, designed and manufactured in accordance with an nec quality assurance program stricter than the standard one, which are designed for such application as any failure or malfunction of the produc ts (sets) or parts/components incorporated therein a customer uses might directly cause any damage to death, human bodily injury or other property, or such application under more severe condition than that defined in the standard quality grade without such direct damage. examples: control systems for transp ortation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, medical equipment not specifically designed for life support, safety equipment, etc. the specific quality grade applies to the products developed, designed and manufactured in accordance with the standards or quality assurance program designated by a customer who requires an extremely higher level of reliability and quality for such products. examples: military systems, aircraft control equipment, aerospace equipment, nuclear reactor control systems, medical equipment/devices /systems for life support, etc. the quality grade of this product is the "standard" unless otherwise specified in this document. www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 3 contents introduction ................................................................................................................... .......................2 1. outline..................................................................................................................... ...............................4 1.1 structure and princi ple.................................................................................................... .......4 1.2 application................................................................................................................ .......................4 1.3 features................................................................................................................... ..........................4 2. general sp ecificat ions ...................................................................................................... ..........5 3. block diag ram ............................................................................................................... ....................6 4. detailed sp ecificat ions ..................................................................................................... ..........7 4.1 mechanical specifica tions.................................................................................................. ....7 4.2 absolute m aximum ratings ................................................................................................... .7 4.3 electrical c haracteristics................................................................................................. ..8 4.3.1 lcd panel signal processing board ........................................................................................ .......8 4.3.2 backlight lamp........................................................................................................... ....................9 4.3.3 power supply voltage ripple.............................................................................................. ...........10 4.3.4 fuse..................................................................................................................... .........................10 4.4 power supply vol tage sequence ........................................................................................ 11 4.5 connections and function s for interface pins.........................................................12 4.5.1 lcd panel signal processing board ........................................................................................ .....12 4.5.2 backlight lamp........................................................................................................... ..................14 4.5.3 positions of plug and socket ............................................................................................. ...........15 4.6 lvds data input map ........................................................................................................ ...........16 4.6.1 mode a ................................................................................................................... .....................16 4.6.2 mode b ................................................................................................................... .....................17 4.6.3 mode c ................................................................................................................... .....................18 4.7 display colors and input data signals ..........................................................................19 4.8 input si gnal ti mings....................................................................................................... ...........20 4.8.1 timing characteristics ................................................................................................... ...............20 4.8.2 input signal timing chart ................................................................................................ ..............20 4.9 display positi ons.......................................................................................................... ...............21 4.10 ten-bit look up table for gamma adjustment............................................................22 4.11 lut serial co mmucation timings .....................................................................................25 4.11.1 timing chart ............................................................................................................ ..................25 4.11.2 timing specifications ................................................................................................... ..............26 4.12 optics.................................................................................................................... ...........................27 4.12.1 optical characteristics................................................................................................. ...............27 4.12.2 definition of contrast ratio............................................................................................ .............28 4.12.3 definition of luminance uniformity ...................................................................................... .....28 4.12.4 definition of response times ............................................................................................ ..........28 4.12.5 definition of viewing angles............................................................................................ ..........28 5. reliability tests........................................................................................................... ..................29 6. pre cautio ns ................................................................................................................. ......................30 6.1 meaning of c aution signs ................................................................................................... ...30 6.2 caut ions ................................................................................................................... .......................30 6.3 attentions ................................................................................................................. .....................30 6.3.1 handling of the product .................................................................................................. .............30 6.3.2 environment.............................................................................................................. ...................31 6.3.3 characteristics.......................................................................................................... ....................32 6.3.4 other .................................................................................................................... ........................32 7. outline drawing s ............................................................................................................ ...............33 7.1 front view ................................................................................................................. .....................33 7.2 rear view .................................................................................................................. ......................34 www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 4 1. outline 1.1 structure and principle color lcd module nl160120bc27-14 module is composed of the amorphous silicon thin film transistor liquid crystal display (a-si tft lcd) pa nel structure with driver lsis for driving the tft (thin film transistor) array and a backlight. the a-si tft lcd panel structure is injected liquid crystal material into a narrow gap between the tft array glass substrate and a color-filter glass substrate. color (red, green, blue) data signals from a host system (e.g. signal generator, etc.) are modulated into best form for active matrix system by a signal processi ng board, and sent to the driver lsis which drive the individual tft arrays. the tft array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly, when it is controlled by data signals. co lor images are created by regulating the amount of transmitted light through the tft array of red, green and blue dots. 1.2 application ? monitor for pc 1.3 features ? ultra-wide viewing angle (adoption of super-advanced super fine tft (sa-sft)) ? wide color gamut ? high resolution ? lvds interface ? adjustable gamma characteristics by using built-in 10-bit lut (look up table) ? selectable lvds data input map ? small foot print ? incorporated edge light type backlight (without inverter) ? acquisition product for ul60950-1/csa c22.2 no.60950-1-03 (file number: e170632) www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 5 2. general specifications display area 432.0 (h) 324.0 (v) mm diagonal size of display 54cm (21.3 inches) drive system a-si tft active matrix display color 16,777,216 colors pixel 1,600 (h) 1,200 (v) pixels pixel arrangement rgb (red dot, green dot, blue dot) vertical stripe dot pitch 0.090 (h) 0.270 (v) mm pixel pitch 0.270 (h) 0.270 (v) mm module size 457.0 (w) 350.0 (h) 25.0 (d) mm (typ.) weight 3,750g (typ.) contrast ratio 550:1 (typ.) viewing angle at the contrast ratio 10:1 ? horizontal: right side 85 (typ.), left side 85 (typ.) ? vertical: up side 85 (typ.), down side 85 (typ.) designed viewing direction viewing angle with optimum grayscale ( =2.2): normal axis (perpendicular) polarizer surface antiglare polarizer pencil-hardness 2h (min.) [by jis k5400] color gamut at lcd panel center 72% (typ.) [against ntsc color space] response time ton+toff (10% 90%) 20ms (typ.) luminance at ibl= 6.0marms / lamp 250cd/m 2 (typ.) signal system 2 ports lvds interface (thc63lvd824 thine electronics, inc. or equivalent) [ rgb 8-bit signals, data enable signal (de), dot clock (clk) ] power supply voltage lcd panel signal processing board: 12.0v backlight edge light type: 6 cold cathode fluorescent lamps (without inverter) power consumption at ibl= 6.0marms / lamp, checkered flag pattern 30.7w (typ., power dissipation of the inverter is not included.) www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 6 3. block diagram note1: connections between gnd (signal ground), fg (frame ground) and vblc (lamp low voltage terminal) in the lcd module gnd - fg connected gnd - vblc not connected fg - vblc not connected note2: gnd and fg must be connected to customer e quipment's ground, and it is recommended that gnd, fg and customer inverter ground are connect ed together in customer equipment. controller i/f lcd module (product) da0+ da0- da1+ da1- da2+ da2- cka+ cka- da3+ da3- db0+ db0- db1+ db1- db2+ db2- ckb+ ckb- db3+ db3- txsel0 txsel1 cs sdato sdati sclk vdd fg gnd vblh1/2/3 vblh4/5/6 vblc1/2/3 vblc4/5/6 h-driver v-driver 4,800 lines tft lcd panel 1,200 lines h: 1,600 3 (r, g, b) v: 1,200 dc/dc converter backlight (edge light type) thc63lvd824 (thine electroni cs, inc.) or equivalent 100 ? 100 ? 100 ? 100 ? 100 ? 100 ? 100 ? 100 ? 100 ? 100 ? fuse power supply for gradation note1, note2 note1 www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 7 4. detailed specifications 4.1 mechanical specifications parameter specification unit module size 457.0 +0.4/-0.3 (w) 350.0 +0.4/-0.3 (h) 25.0 0.3 (d) note1, note2 mm display area 432.0 (h) 324.0 (v) note1 mm weight 3,750 (typ.), 4,000 (max.) g note1: excluding warpage of the signal processing board cover and the connection board cover note2: see " 7. outline drawings ". 4.2 absolute maximum ratings parameter symbol rating unit remarks lcd panel signal processing board vdd -0.3 to +14.0 v power supply voltage lamp voltage vblh 3,000 vrms - input signal voltage note1 vi -0.3 to +2.8 v vdd= 12.0v storage temperature tst -20 to +60 c - front surface topf 0 to +55 c note2 operating temperature rear surface topr 0 to +65 c note3 95 % ta 40 c 85 % 40 c < ta 50 c relative humidity note4 rh 70 % 50 c < ta 55 c absolute humidity note4 ah 73 note5 g/m 3 ta > 55 c operating altitude - 4,850 m 0 c ta 55 c storage altitude - 13,600 m -20 c ta 60 c note1: da0+/-, da1+/-, da2+/-, da3+/-, cka+/-, db0+/-, db1+/-, db2+/-, db3+/-, ckb+/- cs, sdati, sclk, txsel0, txsel1 note2: measured at center of lc d panel surface (including self-heat) note3: measured at center of lcd module's rear shield surface (including self-heat) note4: no condensation note5: water amount at ta= 55c and rh= 70% www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 8 4.3 electrical characteristics 4.3.1 lcd panel signal processing board (ta= 25 c) parameter symbol min. typ. max. unit remarks supply voltage vdd 10.8 12.0 13.2 v - supply current idd - 310 note1 700 note2 ma at vdd= 12.0v ripple voltage vrp - - 100 mvp-p for vdd high vth - - +100 mv differential input threshold voltage low vtl -100 - - mv at vcm= 1.2v note3, note4 input voltage swing vi 0 - 2.4 v note4 terminating resistance rt - 100 - ? - high vih keep this pin open. - control signal input threshold voltage low vil 0 - 0.5 v control signal input current low iil -10 - 10 a note5 high v+ - 1.4 1.9 v low v- 0.4 0.7 - v serial communication signal input threshold voltage hysteresis vh 0.3 - - v note6 high voh 1.9 - - v output signal threshold voltage low vol - - 0.4 v high ioh -4 - - ma output signal current low iol - - 4 ma note7 note1: checkered flag pattern (by eiaj ed-2522) note2: pattern fo r maximum current note3: common mode voltage for lvds driver note4: da0+/-, da1+/-, da2+/-, da3+/-, cka+/-, db0+/-, db1+/-, db2+/-, db3+/-, ckb+/- note5: t x sel0, t x sel1 note6: cs, sdati, sclk note7: sdato www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 9 4.3.2 backlight lamp (ta= 25 c, note1) parameter symbol min. typ. max. unit remarks lamp current ibl 3.0 6.0 7.0 marms at ibl= 6.0marms: l= 250cd/m 2 (typ.) note3 lamp voltage vblh - 750 - vrms note2, note3 1,220 - - vrms ta= 25 c note2, note3, note4 lamp starting voltage vs 1,460 - - vrms ta= 0 c note2, note3, note4 lamp oscillation frequency fo 50 56 60 khz note5 note1: this product consists of 6 backlight la mps, and these specifications are for each lamp. note2: the lamp voltage cycle between lamps should be kept on a same phase. "vs" and "vblh" are the voltage value between low voltage side (cold) and high voltage side (hot). note3: the asymmetric ratio of working waveform for lamps (lamp voltage peak ratio, lamp current peak ratio and waveform space ratio) should be less than 5 % (see the following figure.). if the waveform is asymmetric, dc (direct current) element apply into the lamp. in this case, a lamp lifetime may be shortened, because a distribution of a lamp enclosure substance inclines toward one side between low voltage terminal (cold terminal) and high voltage terminal (hot terminal). when designing the inverter, evaluate asymmetric of lamp working waveform sufficiently. pa: supply voltage/current peak for positive, pb: supply voltage/current peak for negative sa: waveform space for positive part, sb: waveform space for negative part note4: the inverter should be designed so that the lamp starting voltage can be maintained for more than 1 second. otherwise the lamp may not be turned on. note5: in case "fo" is not the recommended value, beat noise may display on the screen, because of interference between "fo" and "1/th". recommended value of "fo" is as following. th: horizontal cycle period (see " 4.8.1 timing characteristics ".) n: natural number (1, 2, 3 ???????? ) note6: method of lamp cable installation may invite fluctuation of lamp current and voltage or asymmetric of lamp working waveform. when designing method of lamp cable installation, evaluate the fluctuation of lamp current, voltage and working waveform sufficiently. pa pb sa sb 0 | pa - pb | pb 5 % 5 % | sa - sb | sb fo= 1 4 1 th (2n-1) www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 10 4.3.3 power supply voltage ripple this product works, even if the ripple voltage leve ls are beyond the permissible values as following the table, but there might be noise on the display image. power supply voltage ripple voltage note1 (measure at input terminal of power supply) unit vdd 12.0v 100 mvp-p note1: the permissible ripple voltage includes spike noise. 4.3.4 fuse fuse parameter type supplier rating fusing current remarks 1.25a vdd fcc16132ab kamaya electric co., ltd. 32v 2.5a, 5 seconds maximum note1 note1: the power supply capacity should be more than the fusing current. if it is less than the fusing current, the fuse may not blow in a short time, and then nasty smell, smoke and so on may occur. www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 11 4.4 power supply voltage sequence *1: da0+/-, da1+/-, da2+/-, da3+/-, cka+/- , db0+/-, db1+/-, db2+ /-, db3+/-, ckb+/- *2: lvds signals should be meas ured at the terminal of 100 ? resistance. note1: in terms of voltage variation (voltage dr op) while vdd rising edge is below 10.8v, a protection circuit may work, and then this product may not work. note2: lvds signals and cs, sdati, sclk must be low or high-impedance, exclude the valid period (see above sequence diagram), in order to avoid that internal circuits is damaged. if some of signals are cut while this product is working, even if the signal input to it once again, it might not work normally. vdd should be cut when the display and function signals are stopped. note3: at the beginning of the serial communication mode, take 20ms or more after the lvds signal input. when writing and reading the lut data, see ? 4.10 ten-bit look up table for gamma adjustment ?. note4: the backlight should be turned on within the valid period of lvds signals, in order to avoid unstable data display. 0ms < t < 35ms 10ms < t < 35ms 10ms < t < 35ms 9.6v 0.1ms < tr < 80ms valid period 10.8v 0v vdd note1 toff > 200ms 0v vdd dip < 20ms 10.8v 10.8v t 20ms note3 valid period lvds signals *1,*2 note2 cs, sdati, sclk note2 on off 0v on www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 12 4.5 connections and functions for interface pins 4.5.1 lcd panel signal processing board (1) cn1 socket (lcd module side): df19g-30p-1h (56) (hirose electric co., ltd. (hrs)) adaptable plug: df19-30s-1c (hirose electric co., ltd. (hrs)) pin no. symbol signal remarks 1 da0- 2 da0+ pixel data a0 odd pixel data input (lvds differential signal) note1 3 da1- 4 da1+ pixel data a1 odd pixel data input (lvds differential signal) note1 5 da2- 6 da2+ pixel data a2 odd pixel data input (lvds differential signal) note1 7 gnd ground signal ground note2 8 cka- 9 cka+ pixel clock odd pixel clock input (lvds differential signal) note1 10 da3- 11 da3+ pixel data a3 odd pixel data input (lvds differential signal) note1 12 db0- 13 db0+ pixel data b0 even pixel data input (lvds differential signal) note1 14 gnd ground signal ground note2 15 db1- 16 db1+ pixel data b1 even pixel data input (lvds differential signal) note1 17 gnd ground signal ground note2 18 db2- 19 db2+ pixel data b2 even pixel data input (lvds differential signal) note1 20 ckb- 21 ckb+ pixel clock even pixel clock input (lvds differential signal) note1 22 db3- 23 db3+ pixel data b3 even pixel data input (lvds differential signal) note1 24 gnd ground signal ground note2 txsel1 txsel0 mode 25 txsel0 open open a open low b low open c 26 txsel1 selection of lvds data input map note3, note4 low low a 27 gnd ground signal ground note2 28 vdd 29 vdd 30 vdd power supply 12v note2 note1: twist pair wires with 100 ? (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter. note2: all gnd and vdd terminal s should be used withou t any non-connected lines. note3: this terminal is pulled-up in the product. (pull-up resistance: 50k ? ) note4: see " 4.6 lvds data input map ". www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 13 (2) cn3 socket (lcd module side): sm10b-srss-tb(lf)(sn) (j.s.t. mfg co., ltd.) adaptable plug: shr-10v-s, shr-10v-s-b or 10sr-3s (j.s.t. mfg co., ltd.) pin no. symbol signal remarks 1 rsvd 2 rsvd 3 rsvd reserved keep these pins open. 4 gnd ground signal ground note1 5 cs chip selection for lut communication control note2 6 sdato serial data output for lut output signal 7 sdati serial data input for lut communication control note3 8 sclk serial clock for lut communication control note3 9 gnd ground signal ground note1 10 rsvd reserved keep this pin open. note1: all gnd terminals should be used without any non-connected lines. note2: this terminal is pulled-up in the product. (pull-up resistance: 50k ? ) note3: these terminals are pulled-down in the product. (pull-down resistance: 50k ? ) www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 14 4.5.2 backlight lamp attention: vblh and vblc must be connected correctly. wrong connections will cause electric shock and also break down of the product. cn201 plug (lcd module side): bhsr-02vs-1 (j.s.t. mfg co., ltd.) adaptable socket: sm02b-bhss-1-tb(lf)(sn) sm02b-bhss-1-tb (j.s.t. mfg co., ltd.) pin no. symbol function remarks 1 vblh1 upper side lamp, high vol tage (hot) cable color: pink 2 vblc1 upper side lamp, low volta ge (cold) cable color: gray cn202 plug (lcd module side): bhsr-02vs-1 (j.s.t. mfg co., ltd.) adaptable socket: sm02b-bhss-1-tb(lf)(sn) sm02b-bhss-1-tb (j.s.t. mfg co., ltd.) pin no. symbol function remarks 1 vblh2 upper side lamp, high vol tage (hot) cable color: white 2 vblc2 upper side lamp, low volta ge (cold) cable color: gray cn203 plug (lcd module side): bhsr-02vs-1 (j.s.t. mfg co., ltd.) adaptable socket: sm02b-bhss-1-tb(lf)(sn) sm02b-bhss-1-tb (j.s.t. mfg co., ltd.) pin no. symbol function remarks 1 vblh3 upper side lamp, high voltage (hot) cable color: red 2 vblc3 upper side lamp, low volta ge (cold) cable color: gray cn204 plug (lcd module side): bhsr-02vs-1 (j.s.t. mfg co., ltd.) adaptable socket: sm02b-bhss-1-tb(lf)(sn) sm02b-bhss-1-tb (j.s.t. mfg co., ltd.) pin no. symbol function remarks 1 vblh4 lower side lamp, high vol tage (hot) cable color: pink 2 vblc4 lower side lamp, low volta ge (cold) cable color: gray cn205 plug (lcd module side): bhsr-02vs-1 (j.s.t. mfg co., ltd.) adaptable socket: sm02b-bhss-1-tb(lf)(sn) sm02b-bhss-1-tb (j.s.t. mfg co., ltd.) pin no. symbol function remarks 1 vblh5 lower side lamp, high vol tage (hot) cable color: white 2 vblc5 lower side lamp, low volta ge (cold) cable color: gray cn206 plug (lcd module side): bhsr-02vs-1 (j.s.t. mfg co., ltd.) adaptable socket: sm02b-bhss-1-tb(lf)(sn) sm02b-bhss-1-tb (j.s.t. mfg co., ltd.) pin no. symbol function remarks 1 vblh6 lower side lamp, high voltage (hot) cable color: red 2 vblc6 lower side lamp, low volta ge (cold) cable color: gray www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 15 4.5.3 positions of plug and socket 1 2 cn204 1 2 cn205 1 2 cn206 1 2 cn201 1 2 cn202 1 2 cn203 insert direction rear side 1 30 cn1 1 10 cn3 www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 16 4.6 lvds data input map 4.6.1 mode a pin thc63lvdf83a pin ra2 51 ta0 53 r12 pin s y mbol ra3 52 ta1 54 r13 ta1- 1da0- ra4 54 ta2 57 r14 ta1+ 2da0+ ra5 55 ta3 58 r15 ra6 56 ta4 59 r16 tb1- 3da1- ra7 3 ta5 60 r17 tb1+ 4da1+ ga2 4ta6 63g12 ga3 6tb0 64g13 tc1- 5da2- ga4 7 tb1 65 g14 tc1+ 6da2+ ga5 11 tb2 66 g15 7 gnd ga6 12 tb3 67 g16 tclk1- 8 cka- ga7 14 tb4 68 g17 tclk1+ 9 cka+ ba2 15 tb5 73 b12 ba3 19 tb6 74 b13 td1- 10 da3- ba4 20 tc0 1st 75 b14 td1+ 11 da3+ ba5 22 tc1 76 b15 ba6 23 tc2 77 b16 ba7 24 tc3 78 b17 note3 rsvd 27 tc4 7 rsvd note3 rsvd 28 tc5 8 rsvd de 30 tc6 9 de ra0 50 td0 51 r10 ra1 2td1 52r11 ga0 8 td2 61 g10 ga1 10 td3 62 g11 ba0 16 td4 69 b10 ba1 18 td5 70 b11 note3 rsvd 25 td6 - cl k 31 clkin 10 clk rb2 51 ta0 81 r22 rb3 52 ta1 82 r23 ta2- 12 db0- rb4 54 ta2 83 r24 ta2+ 13 db0+ rb5 55 ta3 84 r25 14 gnd rb6 56 ta4 85 r26 tb2- 15 db1- rb7 3 ta5 86 r27 tb2+ 16 db1+ gb2 4 ta6 91 g22 17 gnd gb3 6tb0 92g23 tc2- 18 db2- gb4 7 tb1 93 g24 tc2+ 19 db2+ gb5 11 tb2 94 g25 gb6 12 tb3 95 g26 tclk2- 20 ckb- gb7 14 tb4 96 g27 tclk2+ 21 ckb+ bb2 15 tb5 99 b22 bb3 19 tb6 100 b23 td2- 22 db3- bb4 20 tc0 2n d 1 b24 td2+ 23 db3+ bb5 22 tc1 2 b25 24 gnd bb6 23 tc2 5 b26 25 txsel0 bb7 24 tc3 6 b27 26 txsel1 note3 rsvd 27 tc4 - 27 gnd note3 rsvd 28 tc5 - 28 vdd note3 rsvd 30 tc6 - 29 vdd rb0 50 td0 79 r20 30 vdd rb1 2td1 80r21 gb0 8 td2 89 g20 gb1 10 td3 90 g21 bb0 16 td4 97 b20 bb1 18 td5 98 b21 note3 rsvd 25 td6 - cl k 31 clkin - input data note1 transmitter thc63lvd823 cn1 odd pixel data and control signal even pixel data n ote2 www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 17 4.6.2 mode b pin ra7 51 txin0 pin s y mbol ra6 52 txin1 ta1- 1da0- ra5 54 txin2 ta1+ 2da0+ ra4 55 txin3 ra3 56 txin4 tb1- 3da1- ra2 3txin6 tb1+ 4da1+ ga7 4txin7 ga6 6txin8 tc1- 5da2- ga5 7txin9 tc1+ 6da2+ ga4 11 txin12 7 gnd ga3 12 txin13 tclk1- 8cka- ga2 14 txin14 tclk1+ 9cka+ ba7 15 txin15 ba6 19 txin18 td1- 10 da3- ba5 20 txin19 1st td1+ 11 da3+ ba4 22 txin20 ba3 23 txin21 ba2 24 txin22 note3 rsvd 27 txin24 note3 rsvd 28 txin25 de 30 txin26 ra1 50 txin27 ra0 2txin5 ga1 8txin10 ga0 10 txin11 ba1 16 txin16 ba0 18 txin17 note3 rsvd 25 txin23 cl k 31 clkin rb7 51 txin0 rb6 52 txin1 ta2- 12 db0- rb5 54 txin2 ta2+ 13 db0+ rb4 55 txin3 14 gnd rb3 56 txin4 tb2- 15 db1- rb2 3txin6 tb2+ 16 db1+ gb7 4txin7 17gnd gb6 6txin8 tc2- 18 db2- gb5 7txin9 tc2+ 19 db2+ gb4 11 txin12 gb3 12 txin13 tclk2- 20 ckb- gb2 14 txin14 tclk2+ 21 ckb+ bb7 15 txin15 bb6 19 txin18 td2- 22 db3- bb5 20 txin19 2nd td2+ 23 db3+ bb4 22 txin20 24 gnd bb3 23 txin21 25 txsel0 bb2 24 txin22 26 txsel1 note3 rsvd 27 txin24 27 gnd note3 rsvd 28 txin25 28 vdd note3 rsvd 30 txin26 29 vdd rb1 50 txin27 30 vdd rb0 2txin5 gb1 8txin10 gb0 10 txin11 bb1 16 txin16 bb0 18 txin17 note3 rsvd 25 txin23 cl k 31 clkin input data note1 cn1 transmitter ds90cf383, c385 odd pixel data and control signal n ote2 even pixel data www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 18 4.6.3 mode c pin ra0 51 txin0 pin s y mbol ra1 52 txin1 ta1- 1da0- ra2 54 txin2 ta1+ 2da0+ ra3 55 txin3 ra4 56 txin4 tb1- 3da1- ra5 3txin6 tb1+ 4da1+ ga0 4txin7 ga1 6txin8 tc1- 5da2- ga2 7txin9 tc1+ 6da2+ ga3 11 txin12 7 gnd ga4 12 txin13 tclk1- 8cka- ga5 14 txin14 tclk1+ 9cka+ ba0 15 txin15 ba1 19 txin18 td1- 10 da3- ba2 20 txin19 1st td1+ 11 da3+ ba3 22 txin20 ba4 23 txin21 ba5 24 txin22 note3 rsvd 27 txin24 note3 rsvd 28 txin25 de 30 txin26 ra6 50 txin27 ra7 2txin5 ga6 8txin10 ga7 10 txin11 ba6 16 txin16 ba7 18 txin17 note3 rsvd 25 txin23 cl k 31 clkin rb0 51 txin0 rb1 52 txin1 ta2- 12 db0- rb2 54 txin2 ta2+ 13 db0+ rb3 55 txin3 14 gnd rb4 56 txin4 tb2- 15 db1- rb5 3txin6 tb2+ 16 db1+ gb0 4txin7 17gnd gb1 6txin8 tc2- 18 db2- gb2 7txin9 tc2+ 19 db2+ gb3 11 txin12 gb4 12 txin13 tclk2- 20 ckb- gb5 14 txin14 tclk2+ 21 ckb+ bb0 15 txin15 bb1 19 txin18 td2- 22 db3- bb2 20 txin19 2nd td2+ 23 db3+ bb3 22 txin20 24 gnd bb4 23 txin21 25 txsel0 bb5 24 txin22 26 txsel1 note3 rsvd 27 txin24 27 gnd note3 rsvd 28 txin25 28 vdd note3 rsvd 30 txin26 29 vdd rb6 50 txin27 30 vdd rb7 2txin5 gb6 8txin10 gb7 10 txin11 bb6 16 txin16 bb7 18 txin17 note3 rsvd 25 txin23 cl k 31 clkin input data note1 transmitter ds90cf383, c385 cn1 odd pixel data and control signal even pixel data n ote2 www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 19 note1: lsb (least significant bit) ? ra0, ga0, ba0, rb0, gb0, bb0 msb (most significant bit) ? ra7, ga7, ba7, rb7, gb7, bb7 note2: twist pair wires with 100 ? (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter. note3: input signal rsvd is not used inside the product, but do not keep this pin open to avoid noise problem. 4.7 display colors and input data signals this product can display in equivalent to 16,777,216 colors in 256 gray scales. also the relation between display colors and input data signals is as the following table. data signal (0: low level, 1: high level) ra7 ra6 ra5 ra4 ra3 ra2 ra1 ra0 ga7 ga6 ga5 ga4 ga3 ga2 ga1 ga0 ba7 ba6 ba5 ba4 ba3 ba2 ba1 ba0 display colors rb7 rb6 rb5 rb4 rb3 rb2 rb1 rb0 g b7 gb6 gb5 gb4 gb3 gb2 gb1 gb0 bb7 bb6 bb5 bb4 bb3 bb2 bb1 bb0 basic colors black blue red magenta green cyan yellow white 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 red gray scale black dark bright red 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 : : 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green gray scale black dark bright green 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 : : 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue gray scale black dark bright blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 : : 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 20 4.8 input signal timings 4.8.1 timing characteristics parameter symbol min. typ. max. unit remarks frequency 1/ tc 60.0 64.5 67.0 mhz pulse width tc 14.9 15.5 - ns lvds transmitter input duty - - clk rise, fall - see the data sheet of lvds transmitter. ns - 13.1 13.3 19.2 s cycle period th 848 860 1,156 clk - horizontal display period thd 800 clk - 1/tv 59 60 61 hz cycle period tv 1,206 1,250 - h - vertical display period tvd 1,200 h - setup time - ns hold time - ns de, data rise, fall - see the data sheet of lvds transmitter. ns - 4.8.2 input signal timing chart tc de clk data (a), (b) tvd= 1200h (fixed) tv thd= 800clk (fixed) th invalid de invalid invalid invalid invalid invalid www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 21 4.9 display positions the following table is the coordinates per pixel odd pixel: ra= red data even pixel: rb= red data ga= green data gb= green data ba= blue data bb= blue data d (1, 1) d (2, 1) ra ga ba rb gb bb d( 1, 1) d( 2, 1) ? ? ? d( x, 1) ? ? ? d(1599, 1) d(1600, 1) d( 1, 2) d( 2, 2) ? ? ? d( x, 2) ? ? ? d(1599, 2) d(1600, 2) ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? d( 1, y) d( 2, y) ? ? ? d( x, y) ? ? ? d(1599, y) d(1600, y) ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? d( 1, 1199) d( 2, 1199) ? ? ? d( x, 1199) ? ? ? d(1599, 1199) d(1600, 1199) d( 1,1200) d( 2, 1200) ? ? ? d( x, 1200) ? ? ? d(1599, 1200) d(1600, 1200) www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 22 4.10 ten-bit look up table for gamma adjustment adjustment of gamma characteristics for each 8-bit rg b color data is possible by using built-in 10-bit lut (look up table) for ga mma characteristics. the lut is set with the serial data. the combinati on of the control command determines the r/w actions.: read, random/sequential address write and individual/simultaneous rgb setting. the serial data is composed as table 1. table1: serial data composition data data name function remarks d31 cmd5 control command d30 cmd4 control command d29 cmd3 control command d28 cmd2 control command d27 cmd1 control command d26 cmd0 control command see table2 and 3. d25 add9 lut address (msb) d24 add8 lut address d23 add7 lut address d22 add6 lut address d21 add5 lut address d20 add4 lut address d19 add3 lut address d18 add2 lut address d17 add1 lut address d16 add0 lut address (lsb) see table4. d15 dummy dummy data ?0? d14 dummy dummy data ?0? d13 dummy dummy data ?0? d12 dummy dummy data ?0? d11 dummy dummy data ?0? d10 dummy dummy data ?0? d9 data9 lut data (msb) d8 data8 lut data d7 data7 lut data d6 data6 lut data d5 data5 lut data d4 data4 lut data d3 data3 lut data d2 data2 lut data d1 data1 lut data d0 data0 lut data (lsb) see table5. www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 23 table2: command table (cmd5 to cmd0: 6-bit) data name parameter remarks cmd5 selection of write/read mode "1": write mode "0": read mode in case of "0", must be set as follows. cmd4: "1", cmd3: "0", cmd2: "1" cmd1: "0", cmd0: "0" cmd4 must be set to "1". - cmd3 selection of random/sequential address write "1": random address write "0": sequential address write - cmd2 must be set to "1". - cmd1 selection of individual/simultaneous rgb setting "1": individual rgb setting "0": simultaneous rgb setting "1": select the color by using add9 and add8. (see table4.) "0": add9 and add8 are invalid. cmd0 must be set to "0". - table3: command combination table (cmd5 to cmd0: 6-bit) cmd5 cmd4 cmd3 cmd2 cmd1 cmd0 mode 1 1 1 1 1 0 random address write, individual rgb setting 1 1 1 1 0 0 random address write, simultaneous rgb setting 1 1 0 1 1 0 sequential address write, individual rgb setting 1 1 0 1 0 0 sequential address write, simultaneous rgb setting 0 1 0 1 0 0 read mode *other combinations are prohibited, and may cause function error. table4: address table (add9 to add0: 10-bit) data name parameter remarks add9 add8 color selection add [ 9:8 ] = 0:0 red 0:1 green 1:0 blue 1:1 on/off selection of gamma correction when "add [ 9:8 ] =1:1", on/off of gamma correction can select according to the gma [ 2:0 ] . (see table6 and table7.) add7 add6 add5 add4 add3 add2 add1 add0 lut address 256 address = 00h - ffh when add [ 9:8 ] = 1:1, add [ 7:0 ] must be set to 00h. www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 24 table5: data table (data15 to data0: 16-bit) data data name parameter remarks data15 dummy data14 dummy data13 dummy data12 dummy data11 dummy data10 dummy dummy data must be set to "0". - data9 data9 data8 data8 data7 data7 data6 data6 data5 data5 data4 data4 data3 data3 data2 data2 data1 data1 data0 data0 [ msb ] 10-bit lut data 000h - 3ffh [ lsb ] - table6: gamma correction table (data15 to data0: 16bit) data data name parameter remarks data15 dummy data14 dummy data13 dummy data12 dummy data11 dummy data10 dummy data9 dummy data8 dummy data7 dummy data6 dummy data5 dummy data4 dummy data3 dummy dummy data must be set to "0". - data2 gma2 data1 gma1 data0 gma0 [ msb ] gma data [ lsb ] see table7. table7: control code gma [ 2:0 ] gma2 gma1 gma0 function 0 0 0 no correction (initial setting) 0 0 1 correction according to the lut data. note1 *other combinations are prohibited, and may cause function error. note1: initial setting of the lut is undefined data. the lut should be enabled by setting of the gma after writing the lut data in all the 256 addresses, in order to avoid undefined data display. note2: transfer the data every power-on, because the lut data isn't stored in the lcd module. note3: as writing and reading the lut data, a noise may appear on the display image. in order to prevent the noise appearing on the display, following measures should be performed. (1) the lut data should be rewritten during invalid period of pixel data (see " 4.8 input signal timings ".). (2) the lut data should be rewritten when the gamma correction is off (gma [ 2:0 ] = 000). www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 25 4.11 lut serial commucation timings 4.11.1 timing chart (1) read timing chart (2) random address write timing chart (3) sequential address write timing chart hi-z hi-z sclk cs sdatai sdatao invalid d31 d30 d16 n/a n/a d1 d0 invalid d31 d30 d15 d0 www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 26 4.11.2 timing specifications parameter symbol min. typ. max. unit remarks sclk frequency 1/tsck - - 5 mhz - sclk pulse width (write) twsck 50 - - ns - sclk pulse width (read) twsck 5 - - tc note1 sdati-sclk setup time tds 50 - - ns - sdati-sclk hold time tdh 50 - - ns - cs-sclk setup time tcs 50 - - ns - cs-sclk hold time tch 50 - - ns - note1: at the read of the serial communication mode, the sclk pulse width (twsck) must be greater than 5clk (5 tc?s). (see " 4.8.1 timing characteristics ".) note2: during the serial communication mode, the display noise may appear because of rewriting the data. to avoid this, rewrite the lut data when the pixel data is invalid or the gamma correction is off (gma [ 2:0 ] = 000). the external noise may cause the data change, refresh the data regularly according to need. tcs tch tds tdh twsck twsck 1.9v(v+) 1.25v 0.4v(v-) 1.9v(v+) 0.4v(v-) 1.9v(v+) 0.4v(v-) tsck sclk sdati cs www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 27 4.12 optics 4.12.1 optical characteristics (note1, note2) parameter condition symbol min. typ. max. unit measuring instrument remarks luminance white at center r= 0 , l= 0 , u= 0 , d= 0 l 200 250 - cd/m 2 bm-5a or sr-3 - contrast ratio white/black at center r= 0 , l= 0 , u= 0 , d= 0 cr 400 550 - - bm-5a or sr-3 note3 luminance uniformity white r= 0 , l= 0 , u= 0 , d= 0 lu - 1.15 1.3 - bm-5a note4 x coordinate wx - 0.313 - - white y coordinate wy - 0.329 - - x coordinate rx - 0.65 - - red y coordinate ry - 0.33 - - x coordinate gx - 0.29 - - green y coordinate gy - 0.61 - - x coordinate bx - 0.14 - - chromaticity blue y coordinate by - 0.079 - - color gamut r= 0 , l= 0 , u= 0 , d= 0 at center, against ntsc color space c 65 72 - % sr-3 note5 black to white ton - 11 20 ms response time white to black toff - 9 20 ms bm-5a note6 note7 right u= 0 , d= 0 , cr 10 r 70 85 - left u= 0 , d= 0 , cr 10 l 70 85 - up r= 0 , l= 0 , cr 10 u 70 85 - viewing angle down r= 0 , l= 0 , cr 10 d 70 85 - bm-5a note8 note1: these are initial characteristics. note2: measurement conditions are as follows. ta= 25 c, vdd= 12.0v, ibl= 6.0marms/lamp, display mode: uxga, horizontal cycle= 1/75.19khz, vertical cycle= 1/60.0hz optical characteristics are measured at lumi nance saturation after 20 minutes from working the product, in the dark room. also measurement methods are as follows. note3: see " 4.12.2 definition of contrast ratio ". note4: see " 4.12.3 definition of luminance uniformity ". note5: these coordinates are found on cie 1931 chromaticity diagram. note6: product surface temperature: topf= 35 c note7: see " 4.12.4 definition of response times ". note8: see " 4.12.5 definition of viewing angles ". 1 photodetector (bm-5a or sr-3) lcd module (product) 50cm www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 28 4.12.2 definition of contrast ratio the contrast ratio is calculated by using the following formula. luminance of white screen luminance of black screen 4.12.3 definition of luminance uniformity the luminance uniformity is calculated by using following formula. maximum luminance from to minimum luminance from to the luminance is measured at n ear the 5 points shown below. 4.12.4 definition of response times response time is measured, the luminance changes from "black" to "white", or "white" to "black" on the same screen point, by photo-detector. ton is the time it takes the luminance change from 10% up to 90%. also toff is the time it takes the luminance change from 90% down to 10% (see the following diagram.). 4.12.5 definition of viewing angles contrast ratio (cr) = luminance uniformity (lu) = 267 800 1,334 200 600 1,000 100% 90% 10% 0% ton toff luminance white black left upper lower normal axis (perpendicular) u d r l 12 o?clock right www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 29 5. reliability tests (note1) test item c ondition judgment high temperature and humidity (operation) 60 2 c, rh= 60%, 240hours display data is white. heat cycle (operation) 0 3 c 1hour 55 3 c 1hour 50cycles, 4hours/cycle display data is white. thermal shock (non operation) -20 3 c 30minutes 60 3 c 30minutes 100cycles, 1hour/cycle temperature transition time is within 5 minutes. no display malfunctions vibration (non operation) 5 to 100hz, 11.76m/s 2 1 minute/cycle x, y, z direction 10 times each directions mechanical shock (non operation) 294m/ s 2 , 11ms x, y, z direction 3 times each directions no display malfunctions no physical damages esd (operation) 150pf, 150 ? , 10kv 9 places on a panel surface note2 10 times each places at 1 sec interval dust (operation) sample dust: no.15 (by jis-z8901) 15 seconds stir 8 times repeat at 1 hour interval no display malfunctions non-operation 15kpa (equivalent to altitude 13,600m) -20 c 3 c 24 hours +60 c 3 c 24 hours low pressure operation 53.3kpa (equivalent to altitude 4,850m) 0 c 3 c 24 hours +55 c 3 c 24 hours no display malfunctions note1: display and appearance are checked under environmental conditions equivalent to the inspection conditions of defect criteria. note2: see the following fi gure for discharge points { { { { { { { { { www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 30 6. precautions 6.1 meaning of caution signs the following caution signs have very important meaning. be sure to read "6.2 cautions" and "6.3 attentions", after understanding these contents! ! this sign has the meaning that customer will be injured by himself or the product will sustain a damage, if customer has wrong operations. this sign has the meaning that customer will get an electrical shock, if customer has wrong operations. this sign has the meaning that customer will be injured by himself, if customer has wrong operations. 6.2 cautions ? do not touch the working backlight. ther e is a danger of an electric shock. ? do not touch the working backlight. there is a danger of burn injury. ? do not shock and press the lcd panel a nd the backlight! there is a danger of breaking, because they are made of gl ass. (shock: to be not greater 294m/s 2 and to be not greater 11ms, pressure: to be not greater 19.6n ( 16mm jig)) 6.3 attentions ! 6.3.1 handling of the product take hold of both ends without touching the circ uit board when the product (lcd module) is picked up from inner packing box to avoid broken down or misadjustment, because of stress to mounting parts on the circuit board. do not hook nor pull cables such as lamp cable, and so on, in order to avoid any damage. when the product is put on the table temporar ily, display surface must be placed downward. when handling the product, take the measures of elec trostatic discharge with such as earth band, ionic shower and so on, because the product may be damaged by electrostatic. the torque for product mounting screws must never exceed 0.735n ? m. higher torque might result in distortion of the bezel. and the length of product mounting screws must be 5.3mm. www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 31 the product must be installed using mounting holes without undue stress such as bends or twist (see outline drawings). and do not add undue stress to any portion (such as bezel flat area). bends or twist described above and undue stress to any portion may cause display mura. recommended installing method: ideal plane "a" is defined by one mounting hole (datum point) and other mounting holes. the ideal plane "a " should be the same plane within 0.3mm. do not press or rub on the sens itive product surface. when cleaning the product surface, use of the cloth with ethanolic liquid such as screen cleaner for lcd is recommended. do not push nor pull the interface connec tors while the product is working. if the lamp cable is attached on the metal part of the product directly, high frequency leak current to the metal part may occur, then the brightness ma y decrease or the lamp may not be turned on. when handling the product, use of an original protection sheet on the product surface (polarizer) is recommended for protection of prod uct surface. adhesive type protec tion sheet may change color or characteristics of the polarizer. 6.3.2 environment do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases. keep the product in packing box with antistatic pouch in room temperature to avoid dusts and sunlight, when storing the product. in order to prevent dew condensation occurring by temperature difference, the product packing box should be opened after enough time being left under the environment of an unpacking room. evaluate the leaving time sufficiently because a situati on of dew condensation occurring is changed by the environmental temperature and humidity. (recommended leaving time: 6 hours or more with packing state) do not operate in high magnetic field. circuit boards may be broken down by it. this product is not designed as radiation hardened. product mounting hole ideal plane "a" mounting hole (datum point) mounting hole www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 32 6.3.3 characteristics the following items are ne ither defects nor failures. response time, luminance and color may be changed by ambient temperature. display mura, flicker, vertical seam or small spot may be observed depending on display patterns. optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change depending on operating time, and especially low temperature, because the lcd has cold cathode fluorescent lamps. do not display the fixed pattern for a long time because it may cause image sticking. use a screen saver, if the fixed pattern is displayed on the screen. the display color may be changed depending on viewing angle because of the use of condenser sheet in the backlight. optical characteristics may be changed depending on input signal timings. the interference noise between input signal frequency for this product's signal processing board and luminance control frequency of the inverter may appear on a display. set up luminance control frequency of the inverter so that th e interference noise does not appear. 6.3.4 other all gnd and vdd terminals should be us ed without any non- connected lines. do not disassemble a product or adjust variable resistors pack the product with original shipping package, in order to avoid any damages during transportation, when returning the product to nec for repair and so on. the lcd module by itself or integrated into end product should be packed and transported with display in the vertical position. otherwise the display characteristics may be degraded. www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 33 7. outline drawings 7.1 front view unit: mm note1: not shown tolerances of the dimensions are ? m. note3: the length of product mounting screws from surface of plate must be 5.3mm. note4: the values in pare ntheses are for reference. www.datasheet.co.kr datasheet pdf - http://www..net/
nl160120bc27-14 data sheet dod-pd-1335 (1st edition) 34 7.2 rear view unit: mm note1: not shown tolerances of the dimensions are ? m. note3: the values in pare ntheses are for reference. www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of NL160120BC2714

	To Download NL160120BC2714 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .